Just How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Just How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Blog Article
We've found this great article about How to Install a Bathtub Yourself listed below on the internet and think it made sense to talk about it with you over here.
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily obtainable, the job can move immediately; if you have to open up a wall surface to remove the old bathtub and place the new bath tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a contractor to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will aid you set up a new tub in your bathroom if you have actually already acquired a new bathtub as well as do not need to change the plan of your previous water pipes.
Your devices as well as product list should make up the following:
Planning for the Installation
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of removing the existing taps can be fairly bothersome because of the limited gain access to that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the called for setting. The wooden boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the tub up until the level checks out degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water as well as examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the tub as well as likewise examine the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait until the bathtub has been utilized at the very least once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in location between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in issues with moisture and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can split fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our section about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for spending some time to read our content. Liked our piece of writing? Please share it. Help somebody else check it out. Thanks a bunch for your time. Don't forget to check up our site back soon.
Click Here To Find Out More
Report this page